1
00:00:02,690 --> 00:00:11,330
in this video you will learn how to use the occlusal transfer calibration object

2
00:00:11,330 --> 00:00:15,548
the occlusal transfer calibration object is used for calibrating the position of

3
00:00:15,548 --> 00:00:20,759
mounted models from a physical articulated to a virtual articulator

4
00:00:20,760 --> 00:00:25,240
you can calibrate your physical articulated with its virtual version by

5
00:00:25,239 --> 00:00:29,570
mounting the calibration object in gypsum in the articulator and

6
00:00:29,570 --> 00:00:33,939
transferring the object position to transfer plates and then the software

7
00:00:33,939 --> 00:00:40,049
that allows you to transfer the budget in order to skip the bites can later

8
00:00:40,049 --> 00:00:44,859
during scanning any models mounted in the chosen articulator if you have

9
00:00:44,859 --> 00:00:49,909
multiple articulated it should be done for each of them the calibration object

10
00:00:49,909 --> 00:00:53,619
can be used with all the transfer plates and articulate is available in the

11
00:00:53,619 --> 00:00:59,829
dental system as well as all scanners except the d500 the occlusal transfer

12
00:00:59,829 --> 00:01:06,158
calibration object consists of two parts the upper with two convex spots and the

13
00:01:06,159 --> 00:01:13,390
lower with two corresponding indentations

14
00:01:13,390 --> 00:01:17,340
first mount the lower part of the illegal transfer calibration object

15
00:01:17,340 --> 00:01:22,920
under cast mounting played in the articulator the contact surface of both

16
00:01:22,920 --> 00:01:28,099
parts should be located approximately in the sagittal plane of the articulator

17
00:01:28,099 --> 00:01:33,390
and the incisor indicator should be aligned with the vertical not on the

18
00:01:33,390 --> 00:01:37,978
calibration object when the lower part has been mounted attach the upper part

19
00:01:37,978 --> 00:01:43,459
aligning the matching not cures and mounted with gypsum now when the

20
00:01:43,459 --> 00:01:47,019
calibration object has been mounted in the articulator you can launch scan

21
00:01:47,019 --> 00:01:50,709
sweet application

22
00:01:50,709 --> 00:01:52,899
in the Tools tab

23
00:01:52,900 --> 00:01:58,090
OpenManage interface plates and click Add button

24
00:01:58,090 --> 00:02:02,728
the calibrate articulated interface window will open in the Type drop-down

25
00:02:02,728 --> 00:02:07,109
menu select your title particular

26
00:02:07,109 --> 00:02:13,259
and below feelin it identified in the provided field

27
00:02:13,259 --> 00:02:19,019
then press Continue the pop-up window gives you a hint on how to insert the

28
00:02:19,019 --> 00:02:23,569
object in the scanner depending on the type of SCANA

29
00:02:23,568 --> 00:02:28,818
now open your scan and remove its height adapters or adapter if you do not use

30
00:02:28,818 --> 00:02:35,199
the D 2000

31
00:02:35,199 --> 00:02:37,449
then remove

32
00:02:37,449 --> 00:02:48,169
out of clues all transfer calibration object from the articulator

33
00:02:48,169 --> 00:02:59,619
and set it on transfer plates for that articulator set apart on the right side

34
00:02:59,620 --> 00:03:01,610
and the lower

35
00:03:01,610 --> 00:03:05,230
on the left side

36
00:03:05,229 --> 00:03:08,500
close the scanner

37
00:03:08,500 --> 00:03:14,189
and click Continue to start calibration users cannot other than the D 2000 you

38
00:03:14,189 --> 00:03:18,930
will have to do that process separately for the lower and the upper part after

39
00:03:18,930 --> 00:03:23,050
calibration has finished the transfer plates for that article later added to

40
00:03:23,050 --> 00:03:24,560
the list

41
00:03:24,560 --> 00:03:27,719
the transfer of the position of the mountain models from the physical

42
00:03:27,719 --> 00:03:32,810
articulator to the virtual one has now been calibrated and models mounted in

43
00:03:32,810 --> 00:03:40,110
the articulator can now began

44
00:03:40,110 --> 00:03:44,920
you can check the occlusal contacts using occlusal paper and then use the

45
00:03:44,919 --> 00:03:49,649
contact points as reference points in conjunction with a digital scan

46
00:03:49,650 --> 00:04:09,879
remove their clothes will transfer calibration object from the US Canada

47
00:04:09,879 --> 00:04:11,789
said the mountain models on

48
00:04:11,789 --> 00:04:16,560
lights and it said the models in the scanner height adapter is not required

49
00:04:16,560 --> 00:04:21,149
during that process the lower model should be set on the left side and upper

50
00:04:21,149 --> 00:04:34,609
on the right side

51
00:04:34,610 --> 00:04:52,330
create a new case

52
00:04:52,329 --> 00:04:54,579
then launched the scan it dental scheme

53
00:04:54,579 --> 00:04:58,209
occasion in the interface plates drop-down list choose the correct

54
00:04:58,209 --> 00:05:02,698
articulated interface plates and start scanning scanning of my will not be

55
00:05:02,699 --> 00:05:07,860
necessary first gained the upper model on the initial scan set an annotation

56
00:05:07,860 --> 00:05:13,810
and select the area of interest and click Next

57
00:05:13,810 --> 00:05:19,780
select the area of interest on the lower model and click Next

58
00:05:19,779 --> 00:05:23,939
now these guys are ready and due to the transfer of positions from the physical

59
00:05:23,939 --> 00:05:28,389
articulated the bite has been set automatically there is no need for

60
00:05:28,389 --> 00:05:38,900
scanning dies if you scan dies in the art auction

61
00:05:38,899 --> 00:05:44,769
wedding designer you can use the virtual articular to corresponding to the

62
00:05:44,769 --> 00:05:49,479
physical one with the model position transferred

63
00:05:49,480 --> 00:05:53,530
you can use the previously marked occlusal contact points as a reference

64
00:05:53,529 --> 00:05:59,199
for checking the transfer precision

65
00:05:59,199 --> 00:06:02,209
we hope our video was helpful thank you for watching